Dosimetric characteristic of a new 125I brachytherapy source

A new brachytherapy (125)I source has been investigated at Iranian Agricultural, Medical and Industrial Research School. Dosimetric characteristics [dose-rate constant Λ, radial dose function g(l)(r) and anisotropy function F(r,)] of IRA-(125)I were theoretically determined in terms of the updated AAPM task group 43 (TG-43U1) recommendations. Versions 5 and 4C of the Monte Carlo radiation transport code were used to calculate the dosimetry parameters around the source. The Monte Carlo calculated dose-rate constant of the (125)I source in water was found to be 92×10(-4) Gy h(-1) U(-1) with an approximate uncertainty of ±3 %. Brachytherapy seed model, 6711-(125)I, carrying (125)I radionuclides, was modelled and benchmarked against previously published values. Finally, the calculated results were compared with the published results of those of other source manufacturers.     

An experimental investigation into the performance of a domestic thermosyphon solar water heater under varying operating conditions

An experimental investigation has been carried out on a thermosyphon solar water heater. The system consisted of a flat-plate collector of 1.5 m² absorber area with 21 tubes/m width and storage tank of 125 litre capacity. Experiments were carried out for both cloudy and clear weather conditions in winter and summer. The hourly system performance was evaluated for all test conditions. The final mean tank temperature was measured daily which enabled the calculation of the possible contribution of solar energy for domestic hot water supply in Basrah, Iraq (latitude 30.76°N). The system was tested at both no-load and loading conditions. Intermittent and continuous load was imposed, and system performance was evaluated for each condition.     

Recycling value of building materials in building assessment systems

The selection of green building materials and products is by far the most controversial task in sustainable construction. Determining the merits of building materials and products in terms of their recycling value, which seems to be a simple matter, is a very controversial topic in building assessment systems. This paper suggests a method to assess energy savings by recycling building materials, which can be a potential indicator of recycling worth. The method takes account of material selection, construction and deconstruction technologies, and the frequency of recycling. The result of this study can be used in assessment tools as a factor separate from the embodied energy. Since embodied energy affects the potential recycling energy, another factor is defined, based on these two factors, in order to make it possible to compare and select materials correctly, based on their embodied energy and recycling potential.     

Comparative studies on protein fractions and amino acid composition from sorghum and pearl millet

A defatted flour sample of sorghum and pearl millet were separated into three fractions. These procedures involve extracting the defatted flour with aqueous sodium hydroxide (pH 11.9) followed by precipitation with diluted HCl acid (pH 4.8). The two protein fractions I (soluble at pH 4.8) and II (insoluble at pH 4.8) along with the remaining residues (fraction III) were lyophilized separately. The amino acid composition of the original flour and the three fractions were determined. Lysine seems to be the most deficient amino acid in the original flour and the remaining residues. Fraction I and II, in which the lysine accumulated, have essentially better amino acid profile and consequently nutritionally better quality than the protein of the original defatted flour. The recovered protein-rich fractions I and II should be useful as a protein ingredient in foods. The remaining residues can be extruded into convenience foods.     

Changes in blocking mechanisms during membrane processing of pomegranate juice

The effect of pressure, velocity, pretreatment, membrane type and pore size on fouling mechanisms were evaluated. Pomegranate juice was treated with polyvinylidene fluoride (PVDF) 0.22 μm and mixed cellulose ester (MCE) 0.1 μm at different pressures. Cake formation which was the dominant mechanism was formed in the first stages of process and, as the filtration proceeded, intermediate, standard, and complete blocking, respectively occurred at higher pressure (5 kPa). At lower pressure (0.5 kPa) the last mechanism did not occur. Results showed that cake formation was the only mechanism in MCE 0.22 μm, however, others occurred with MCE 0.1 μm and PVDF 0.22 μm. Using MCE 0.22 μm prior to MCE 0.025 μm can reduce the role of cake formation in pore blocking. Evaluation of the impact of velocity showed that at the higher velocity (0.53 m s⁻¹) the complete blocking occurred faster than at the lower velocity (0.09 m s⁻¹).     

DC and AC electrical conductivity of electro-deposited carbon-black–epoxy composite films

Carbon-black–epoxy composite films were prepared by cathodic electro-deposition of a dispersion containing carbon black and epoxy resins. The films, after baking at elevated temperature, show a semi-conducting behavior. Using DC conductivity measurements it was possible to determine the glass transition temperature of the samples, the conductivities of which lie in the sensitivity range of the instrument. Conductive samples show a positive temperature coefficient both below and above T_g. Based on the electrical impedance data extracted from the electrochemical impedance spectra, the exponents x and y were determined for the frequency dependence of the complex conductivity and complex dielectric constant as 0.8 and 0.2, respectively. These values are in good agreement with the classical values of x = 0.72 and y = 0.28. It was also found that these exponents are the same for all the CCB contents studied.     

Qualitative and quantitative evaluation of heart sound reduction from lung sound recordings

Recursive least squares (RLS) adaptive noise cancellation (ANC) and wavelet transform (WT) ANC have been applied and compared for heart sound (HS) reduction from lung sounds (LS) recordings. Novel processes for quantitative and qualitative evaluation of any method for HS reduction from LS have also been proposed.     

The dependence of the creep properties of din 1.4970 austenitic stainless steel at 973 K on different thermomechanical pre-treatments

The creep-rupture behaviour of a Type DIN 1.4970 austenitic stainless steel has been investigated at 973 K (700°C) in a high vacuum for three conditions of thermomechanical treatment and a wide range of applied stresses using foil specimens of 105 μm thickness. After solution-annealing at 1373 K (1100°C) for all specimens, the three treatments were: — condition 1: 13% cold-worked — condition2: aged for 24 h at 1073 K (800°C) and 13% cold-worked — condition 3: (“Standard condition”): 13% cold-worked and aged for 24 h at 1073 K (800°C).The rupture lives and the minimum creep rates were found to be highly dependent on the applied stresses. The treatment of condition 1 material yielded a product as strong as the “standard” condition 3, while the condition 2 material was less creep resistant.Structural changes as well as fractography were followed using metallographic, transmission and scanning electron microscope techniques. Transgranular ductile fracture was clearly observed in all three conditions. TEM investigations showed that dispersive TiC precipitates were present in the matrix of condition 3 material before creep testing, contrary to condition 1 and 2 material. In condition 1, the TiC dispersion was already found after short creep times, while no dispersive TiC precipitates were found in condition 2 material in any test condition.     

Healing DNA Self-Assemblies Using Punctures

In self-assembly, individual components (commonly referred to as tiles) have sufficient infor mation to build templates for structures such as lat tices for two-dimensional scaffolds. Tile sets that can heal (fully or partially) an erroneous DNA assembly have been proposed. Healing requires growth to be restarted such that erroneous tiles can be removed and the correct tiles can bind to the aggregate. Punctures have been proposed for this purpose; in this paper, a puncture is intentionally induced in the self-assembly to restart the growth process. The goal of this paper is to characterize an intentionally induced puncture (and its relevant properties) on an erroneous tile site in the grown crystal as part of a healing process. This allows to propagate any newly generated error away from the source of growth (i.e. the seed tile), such that self-assembly can continue along specific directions. Different types of puncture are considered with respect to healing and related features, such as growth direction, error and aggregate types. Punctures are analyzed using a new characterization and metric; different tile sets are investigated in detail for healing of a DNA self-assembly.